Warp Gasification
team@univastum.com
Knowledge Base
Chief Technology Officer
Peter Kalenuk
Industrial Waste-to-Steam
Integrated Waste-to-Steam facility for industrial client
Spain
Municipal Waste-to-Electricity
Modular Waste-to-Energy facility for municipal solid waste
Romania
investors@univastum.com
Chief Investment Officer
Eben Klynsmith
Our Approach
Work With Us
Insights & News
Press Kit
mt@univastum.com
Chief Marketing & Communications Officer
Matthew Tucker

Alternative Fuel Gasification for the Glass Industry

Syngas from MSW, RDF, SRF, Industrial Waste and Biomass for Partial Natural Gas Substitution and Energy Supply at Glass Plants
Waste-to-Energy gasification converts prepared municipal solid waste (MSW), RDF, SRF, industrial waste and biomass into syngas that can be used as an alternative gaseous fuel in glass manufacturing.

WARP gasification technology enables waste-derived syngas to partially substitute natural gas across suitable thermal processes within a glass plant. Key applications include glass melting furnaces, Hot Gas Generators (HGG), annealing lehrs and other gas-fired consumers.

Depending on the plant energy balance, WARP can also be configured with heat recovery and on-site generation of steam, hot water or electricity.

At larger glass plants, syngas can be distributed through a common header to multiple thermal consumers, including the melting furnace, HGG, annealing lehrs and auxiliary furnaces.

Energy Use and Natural Gas Demand in Glass Manufacturing

Glass manufacturing is a continuous, high-temperature and energy-intensive process. Natural gas remains the main energy source for European glass manufacturing.
  • 70–80%
    of sector energy use
  • 20–30%
    electricity represents
  • 20–35%
    of total production costs
This makes continuously operating plants with substantial gaseous-fuel demand particularly relevant for alternative-fuel gasification.
Potential Benefits for Glass Plants
The actual effect depends on feedstock composition, furnace configuration, substitution rate and operating requirements.
Partial natural gas substitution
waste-derived syngas can supplement natural gas in suitable thermal processes.

Fuel diversification
MSW, RDF/SRF, industrial waste and biomass can become part of the plant energy balance through gasification.

Multiple points of use
a common syngas system can supply several thermal consumers.

Heat recovery
sensible heat from hot syngas can be used for preheating, drying, hot water or steam production.

Potential fossil CO₂ reduction
where the fossil emissions associated with syngas are lower than those of the displaced natural gas.

Syngas for the Glass Melting Furnace

The glass melting furnace is normally the largest thermal consumer at a glass plant and therefore
offers the greatest potential for natural gas substitution.
MSW/ RDF / Industrial waste / Biomass → WARP gasification → Syngas conditioning → Syngas / natural gas firing → Glass melting furnace
For Univastum engineering assessments, a scenario of approximately 20–30% of furnace thermal input may be used as an initial calculation case for partial natural gas substitution. This is an engineering assessment scenario, not an industry benchmark, guaranteed performance level or maximum substitution rate.
Natural gas can remain available for backup and thermal-load control.

The achievable rate depends on:
  • burner system design
  • syngas composition, calorific value, flow and pressure
  • flame stability and radiative heat transfer
  • furnace pressure
  • regenerators or recuperators
  • flue-gas system capacity
  • NOx formation
  • glass-quality and process-stability requirements

Syngas Flow, Calorific Value and Furnace Integration

Air-blown gasification produces syngas with a lower calorific value than natural gas. A larger gas volume is therefore required to deliver the same thermal input.

Furnace integration must consider the capacity of burners, syngas headers, control valves, regenerators or recuperators, and the furnace and flue-gas systems.

For large furnace applications, reduction of nitrogen dilution may also be evaluated, including oxygen-enriched gasification where justified by the material and energy balance.

Oxy-Fuel, Electric and Hybrid Glass Melting

Glass manufacturers are evaluating several parallel routes for reducing conventional natural-gas firing, including oxy-fuel combustion, electric melting, electric boosting and hybrid furnaces combining electricity with gaseous fuels.

Oxy-fuel furnaces use oxygen instead of combustion air, substantially reducing nitrogen entering the furnace. Where syngas is considered for an oxy-fuel furnace, compatibility must be assessed specifically for syngas composition and calorific value, oxygen demand, burner design, flame characteristics and furnace atmosphere. It should therefore be treated as a dedicated furnace-integration case rather than as a direct replacement for natural gas.

Hybrid melting combines electrical energy with combustion. The flat-glass line combines electric melting with oxy-fuel combustion. The container-glass sector has also evaluated large-scale hybrid furnace concepts intended to replace a substantial share of natural gas with electricity.
WARP gasification is therefore not necessarily an alternative to furnace electrification. In a hybrid configuration, syngas can potentially supply part of the combustion share of furnace energy demand, while electricity provides another part of the melting energy.
Such configurations may be relevant where grid capacity, energy prices, staged furnace conversion or operational redundancy favour a mixed energy supply. The appropriate balance between electricity, natural gas and syngas must be established for each furnace.

Hot Gas Generators, Batch and Cullet Heating

A lower-complexity integration route is the use of syngas in a standalone Hot Gas Generator.
Waste / RDF / Biomass → WARP gasification module → Syngas → HGG → Hot gas
Hot gas can be used for batch or cullet drying and preheating, raw-material preparation and other auxiliary thermal duties.

Because this configuration limits direct interaction with the glass melting process, it can be considered as an initial brownfield integration route. The actual fuel-saving effect of batch or cullet preheating depends on furnace design, cullet ratio and heat-recovery configuration.

Annealing Lehrs and Other Gas-Fired Consumers

Syngas can also be supplied to annealing lehrs, auxiliary furnaces, gas-fired heating systems and drying equipment.

For container glass, annealing operates at substantially lower temperatures than melting, generally reducing integration complexity. Several consumers can be connected to a common syngas header while natural gas remains available for backup and process control.

Forehearth and Glass Conditioning

Syngas may also be considered for gas-fired working-end and forehearth systems.

Because glass temperature and thermal homogeneity directly affect product quality, this application requires demonstrated stability of syngas composition, pressure and calorific value and is generally more appropriate as a subsequent integration stage.

Where Syngas Can Be Used in a Glass Plant

For a brownfield project, HGG, drying and auxiliary furnaces can provide relatively straightforward initial integration points. The main melting furnace offers the largest potential for natural gas substitution but requires detailed furnace and burner assessment.

Heat Recovery, Steam and Hot Water

Hot syngas contains both chemical energy and sensible heat. Before delivery to the final thermal consumer, part of this heat can be recovered for hot water, steam, combustion-air or process- water preheating, fuel drying and other thermal duties.

For most glass plants, steam is a secondary output rather than the principal use of syngas. Where practical, heat recovery can be combined with retaining the chemical energy of syngas for direct fuel substitution.

Electricity Generation

Part of the syngas can also be used for on-site electricity generation where justified by the plant energy balance. For sites with a large continuous gaseous-fuel demand, direct thermal use of syngas should normally be assessed alongside power generation because it avoids an additional energy-conversion step.

Suitable Fuels

Potential feedstocks for waste-to-energy solution include:
  • Municipal Solid waste (MSW)
  • RDF and SRF
  • suitable industrial waste
  • non-recyclable mixed plastics
  • end-of-life tyres and rubber residues
  • woody biomass
  • agricultural residues
  • prepared MSW-derived fuels
Internal waste streams can be combined with externally sourced fuels where appropriate. Feedstock qualification considers LHV, moisture, ash, chlorine, sulphur, alkalis, metals, composition stability and preparation requirements.

Materials suitable for material recycling should be directed to appropriate recycling routes.

Suitable Glass Plant Size and Energy Demand

The standard WARP design basis used for preliminary project assessment is approximately 5 t/h of prepared fuel, corresponding to about 40,000 t/year at 8,000 operating hours.

These are WARP system design parameters, not general gasification-industry benchmarks. Actual project throughput is defined from the feedstock characteristics and required operating
conditions.

The most relevant applications are therefore continuously operating glass plants with substantial thermal demand.
  • Float Glass

    An average European float-glass plant produces approximately 650 t/day and operates continuously. This scale can support evaluation of one or more gasification modules for partial natural gas substitution.
  • Container Glass

    Large container-glass furnaces typically operate at a scale of several hundred tonnes per day. Particularly relevant sites include those with multiple furnaces, several continuous gas-fired consumers and stable access to prepared alternative fuel. At such sites, syngas can be distributed between the melting furnace, HGG, annealing lehrs and auxiliary consumers.
  • Smaller Specialty-Glass Plants

    For smaller facilities, thermal demand may be insufficient for the standard WARP® design
    basis. Such projects require individual assessment or combination with other industrial energy consumers at the site.

Potential Reduction in Natural Gas Use and CO₂ Emissions

Because natural gas represents approximately 70–80% of energy use in European glass manufacturing, partial fuel substitution can materially change the fossil-energy balance of a plant.

The 2006 IPCC Guidelines for National Greenhouse Gas Inventories give a default CO₂ emission factor for natural gas of 56,100 kg CO₂/TJ, equivalent to 56.1 kg CO₂/GJ, on a net calorific basis.

Reducing natural gas consumption reduces the direct combustion emissions associated with the displaced gas. The net fossil CO₂ effect of waste-derived syngas depends on the fossil and biogenic fractions of the feedstock, waste composition, gasification efficiency, auxiliary energy consumption, fuel preparation and transport, and the applicable carbon-accounting methodology.

Biomass and fuels with a significant biogenic energy fraction can provide a potential reduction in fossil CO₂ emissions. For RDF, MSW-derived fuels and blends containing significant fossil plastics, a reduction relative to natural gas should not be assumed automatically.
CO₂ reduction should therefore be calculated from the actual project fuel composition and energy balance rather than assumed from the use of waste-derived syngas alone.
Lifecycle effects associated with alternative waste-treatment routes, transport or avoided disposal
should be assessed separately from direct emissions at the glass plant.

EU ETS and Carbon Cost

Large glass-manufacturing installations in the European Union are covered by the EU Emissions Trading System (EU ETS). Under the ETS Directive, this includes the manufacture of glass, including glass fibre, with a melting capacity exceeding 20 tonnes per day.

Covered installations are subject to monitoring, reporting and verification requirements, creating a direct economic relationship between fossil-fuel combustion and carbon cost. For a glass plant, partial replacement of natural gas with syngas can affect both fossil CO₂ emissions from fuel combustion and the corresponding EU ETS exposure, subject to the applicable monitoring and accounting rules.

The result depends particularly on the fossil and biogenic fractions of the feedstock. Gasification does not eliminate process CO₂ emissions associated with carbonate raw materials used in glass production; its principal potential effect is on fuel-related emissions.

For hybrid or increasingly electrified furnaces, direct combustion emissions may decrease while electricity consumption rises. The overall assessment should therefore consider both the plant’s EU ETS position and the carbon intensity and cost of electricity.

Integration into an Existing Glass Plant

WARP gasification module can be installed as a separate energy island connected to one or several existing consumers, including:
  • main melting furnace
  • HGG
  • batch and cullet preheating
  • forehearth
  • annealing lehrs
  • auxiliary furnaces
  • boilers
  • electricity-generation equipment
The configuration is determined by furnace characteristics, fuel availability, site energy demand and the required substitution rate. For critical production processes, the existing energy source and appropriate backup logic can be retained.

Cooperation Models

Equipment Supply and Integration

The glass manufacturer owns the energy system. Univastum performs the agreed engineering scope, supplies the process equipment and integrates it with the existing plant infrastructure.

Energy-as-a-Service

The project can also be structured as a long-term energy-supply arrangement. Univastum or a project company develops and operates the system, while the glass plant purchases an agreed volume of syngas, thermal energy and/or electricity. Technical parameters, energy pricing, responsibilities and contract terms are defined for each project.

Information Required for a Preliminary Assessment

Please send us the data for initial assessment:
Glass production
glass type, furnace lines and production capacity in t/day.

Melting furnace
furnace type, thermal capacity, burners, regenerators/recuperators, oxy-fuel or hybrid configuration and electrical boosting where applicable.

Natural gas
hourly and annual consumption, price and operating profile.

Electricity
consumption, maximum demand, available grid capacity and tariffs.
Other thermal consumers
HGG, forehearth, annealing lehrs, dryers and auxiliary furnaces.

Fuel for WARP
type, quantity, composition, LHV, moisture and possible external sources.

Site
available space, utilities, oxygen availability where relevant and potential syngas connection points.

Emissions and EU ETS
applicable emission limits, monitored emissions and relevant carbon-cost assumptions.
Based on these data, our preliminary assessment can define:

  • suitable integration points and indicative number of WARP modules
  • potential thermal substitution
  • required syngas flow and conditioning
  • compatibility with air-fuel, oxy-fuel or hybrid furnace operation
  • preliminary material and energy balance
  • changes in natural gas and electricity consumption
  • indicative CO₂ and EU ETS effect
  • preliminary project economics
Preliminary Technical Concept
The first project stage can compare four main approaches:
  • HGG / batch / cullet heating
    limited interaction with the main melting furnace
  • Auxiliary consumers
    distributed use of syngas in annealing lehrs and other thermal
    equipment
  • Main furnace integration
    partial substitution of natural gas, including air-fuel, oxy-fuel or hybrid configurations
  • Integrated energy configuration
    a common syngas header serving several thermal consumers, with heat recovery and, where justified, electricity generation.
Further development includes the material and energy balance, syngas specification, burner and furnace integration study, emissions and EU ETS assessment, and techno-economic analysis.